CS5466
FREQ[2:0]
IGAIN[1:0]
IIN± PGA
4th Order
??
Sinc 3
IIR
HPF
HPF
Modulator
Current Channel
Digital Filter
Config
E1
?
VIN±
10x
2nd Order
??
Modulator
Sinc 3
IIR
HPF
x
N=400
N
Energy-to-
Pulse Rate
Converter
E2
FOUT
NEG
Digital Filter
Voltage Channel
Figure 2. Data Flow
4.
THEORY OF OPERATION
The CS5466 is a dual-channel analog-to-digital convert-
er (ADC) followed by a computation engine that per-
forms an energy-to-pulse conversion. The flow diagram
for the two data paths is depicted in Figure 2. The ana-
log inputs are structured with two dedicated channels,
voltage and current, then optimized to simplify interfac-
ing to sensing elements.
the IIR filter to compensate for the magnitude roll-off of
the low-pass filtering operation.
An optional digital high-pass filter ( HPF in Figure 2) re-
moves any DC component from the selected signal
path. By removing the DC component from the voltage
or current channel, any DC content will also be removed
from the calculated average active (real) power as well.
The voltage-sensing element introduces a voltage
waveform on the voltage channel input VIN ? and is sub-
4.2
Active Power Computation
ject to a fixed 10x gain amplifier. A second-order delta-
sigma modulator samples the amplified signal for digiti-
zation.
Simultaneously, the current sensing element introduces
a voltage waveform on the current channel input IIN ?
and is subject to four programmable gains. The ampli-
fied signal is sampled by a fourth-order delta-sigma
modulator for digitization. Both converters sample at a
rate of MCLK / 8. The over-sampling provides a wide
dynamic range and simplified anti-alias filter design.
The instantaneous voltage and current data samples
are multiplied to obtain the instantaneous power. The
product is then averaged over 400 conversions to com-
pute the active power value used to drive pulse outputs
E1, E2, and FOUT. Output pulse rate of E1 and E2 can
be set to one of four frequencies to directly drive a step-
per motor or a electromechanical counter or interface to
a microcontroller or infrared LED. The alternating output
pulses of E1 and E2 allows for use with low-cost elec-
tromechanical counters.
4.1
Digital Filters
Output FOUT provides a uniform pulse stream that is
proportional to the active power and is designed for sys-
The decimating digital filters on both channels are Sinc 3
filters followed by fourth-order IIR filters. The single-bit
data is passed to the low-pass decimation filter and out-
put at a fixed word rate. The output word is passed to
10
tem calibration. The FREQ[2:0] inputs set the output
pulse rate of E1, E2, and FOUT. See ”Energy Pulse
Outputs” on page 11. for more details.
DS659F2
相关PDF资料
CS5466-IS IC ENERGY METERING 1PHASE 24SSOP
CS8312YN8 IC PREDRIVER IGBT IGNITION 8DIP
CX1006 SOCKET ADAPTER 40TSOP SUPERPRO5K
CYCLONEMAX CYCLONE MAX FLASH PROGRAM
D-1723-WH DRAWER SLIDING 16.56X6.31X19.18"
D072-0103 DEV KIT 7 NIMBLE SBC/FUSION7/BB
D10B2 SURGE SUPPR NETWORK BNC
D1U-12-CONC 12V D1U OUTPUT CONNECTOR CARD
相关代理商/技术参数
CS5467 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Four-channel Power / Energy IC
CS5467_07 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Four-channel Power / Energy IC
CS5467_11 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:Four-channel Power/Energy IC
CS5467-IS 功能描述:电流和电力监控器、调节器 4-Ch Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5467-ISZ 功能描述:电流和电力监控器、调节器 4-Ch Single Phase Power/Energy IC RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5467-ISZR 功能描述:电流和电力监控器、调节器 IC 4-Ch Single Phase PWR/Energy RoHS:否 制造商:STMicroelectronics 产品:Current Regulators 电源电压-最大:48 V 电源电压-最小:5.5 V 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:HPSO-8 封装:Reel
CS5471 制造商:CIRRUS 制造商全称:Cirrus Logic 功能描述:DUAL CHANNEL DELTA SIGMA ANALOG TO DIGITAL CONVERTER
CS5471-BS 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Cirrus Logic 功能描述: